Neuigkeiten

September 2023
loading...

Introducing the Vaillant cost-attractive wall-mounted buffers for heat pumps

Discover the cost-attractive wall-mounted Vaillant buffers designed to enhance performance and efficiency of heat pump systems. Now available for download on MEPcontent.com.

We are pleased to introduce the cost-attractive wall-mounted Vaillant buffers for heat pumps, designed specifically to enhance the performance and efficiency of heat pump systems. This buffer tank offers a range of key functions and features that make it an essential component for heat pump systems.

The buffer ensures the minimum running time in heating and cooling operation, thanks to sufficient water volume in the heating installation. This helps in limiting heat-pump on-off cycles and resulting in longer compressor lifespan.

The Vaillant buffer tank features two capacities (50L - 100L) to meet a wide range of applications, depending on the size of your customers house, volume of water in the heating circuit, heat pump output, etc. Additionally, it has only four connections, which is enough for simple installation, low heat loss, and optimized cost.

It is also suitable for active cooling, as the buffer tank is fully insulated with polyurethane, preventing any condensation in cooling mode.

For further information, please visit the Vaillant website or your country specific Vaillant website.
August 2023
loading...

Introducing recoVAIR 60/2: The basic ventilation system for reliable heat and humidity control

Discover recoVAIR 60/2 by Vaillant, the new efficient decentralised ventilation system for new buildings and modernisation projects with excellent heat recovery capabilities and simple planning and installation. Now available for download on MEPcontent.com.
As a professional in the construction industry, you need reliable and efficient solutions for heat and humidity control in both new builds and modernisation projects. The Vaillant recoVAIR 60/2 system is designed to meet these demands while also providing a strong price-performance ratio.

One of the key features of the recoVAIR 60/2 is its excellent heat recovery capabilities. The ceramic heat exchanger and push-pull principle ensure that warm air is absorbed and used to heat incoming cold air, resulting in significant energy savings and lower heating bills. Compared to basic ventilation, you can reduce heating costs by up to 30%.

Another advantage of the recoVAIR 60/2 is its simplicity in planning, installation, and commissioning. The small diameter of the stand-alone units provides a high flexibility in installation. Setting up the system is straightforward using DIP switches, and the controls provide clear feedback at every step.

In addition to its technical features, the recoVAIR 60/2 also offers high customer acceptance. Its compact design and discreet covers make it nearly invisible, while the low volume in normal operation can be further reduced through the night mode. Maintenance is quick and cost-effective, with easy replacement of parts and filters that can even be done by customers themselves.

Overall, the recoVAIR 60/2 provides a reliable and efficient solution for heat and humidity control that meets high standards in the construction sector and satisfies the demands of your customers.

The market launch was in June 2023. The launch date may differ in some countries. For further information, please visit the Vaillant website or your country specific Vaillant website.
Mai 2023
loading...

New template for Ubbink Air Excellent products

Trimble MEPcontent created a revised template for the Ubbink-Centrotherm Group, Air Excellent products. This template is in cooperation with the manufacturer Ubbink and companies who are working with the Ubbink Air Excellent products revised, updated, and extended with new products and features.
With this revised template Ubbink offers a better user experience and easier use of their Air Excellent products in your design.
The new and revised topics are:

    The new template is having now separate supply and return (exhaust) systems. This makes it easier to use the calculation methods of Revit.


    New flexible ventilation ducts have been added, it is now possible to design an air distribution system that has the actual pattern as in practice. By choice of the engineer, he can still use the old method of straight flexible air ducts.


    All components have been updated with the connector position where the ductwork enters the meets the length of the sock. With this revision it is easier to make a prefabricated installation with the correct dimensions.


    The height (offset) positions of the valve adapters are made equal to the position adapters on the distribution boxes. They will help to connect the ducts to each other.
    Horizontal and vertical split for the ducts is set in the auto routing preferences. With this revision it is easier for the engineer to design a system to another floor.


    Calculations of flow rate will be more correct because there are no lost airflows through thru the distribution box.


    Trimble has built this template according to the new platform. This feature makes it more flexible to create and publish new or existing localizations (countries or languages where Ubbink deliver the Air Excellent products).


    All descriptions (technical and or extra information) in the accessories are delivered by Ubbink and is equal to their system. With this new data there is no misconception in ordering or communication with Ubbink. All extra documentation and texts correspond to the officially published texts of the Ubbink-Centrotherm Group.


    The improvements have been evaluated by Ubbink in cooperation with external companies approached by Ubbink.


Trimble will publish first the updated Ubbink-NL Air Excellent template. For questions, please contact Ubbink (advies@ubbink.nl), about the products, or the Trimble Helpdesk when using the Template.
April 2023
loading...

“Less is more” met de ComfoAir Flex

De beste dingen in het leven zijn ongezien. Het nieuwe Zehnder ComfoAir Flex ventilatiesysteem combineert een compact ontwerp met topprestaties.

De nieuwe plafond ventilatie-unit ComfoAir Flex:
-- Ruimtebesparend
-- Flexibel voor installatie
-- Zeer laag verbruik
-- Hoog Rendement
-- Ingebouwde vochtsensor: EPB conform
-- Connectivity: Wifi onboard

Lees meer over de ComfoAir Flex op de Zehnder website.

Bespaar gebruiksoppervlakte met de ultra compacte ComfoVar Aero voor de gestapelde woningbouw

De vraag naar duurzaamheid en techniek in woningen groeit. Tegelijkertijd wordt woonoppervlakte kostbaarder. Vanwege de huidige woningnood worden er steeds meer kleine appartementen gebouwd. De ultracompacte ComfoVar Aero is bij uitstek geschikt voor deze kleine woningen. De ComfoVar Aero zorgt dat zoveel mogelijk gebruiksoppervlakte per appartement overblijft.

Meer m2 gebruiksoppervlakte per appartement
Hoge BENG score
Voordelig in onderhoud
Bewezen Zehnder topkwaliteit

Geschikt voor ventilatie met behulp van een luchtbehandelingskast in appartementen tot 360 m3/h. Lees meer over de ComfoVar Aero op de Zehnder website.

BIM-bestanden van Zehnder op MEPcontent
Download de BIM-bestanden van de ComfoAir Flex 250 HRV, de ComfoAir Flex 350 HRV en de ComfoVar Aero DN 160 en vind hier het volledige BIM-aanbod van Zehnder op MEPcontent.com!

Over Zehnder
Zehnder is een toonaangevende wereldwijde leverancier van complete oplossingen voor een gezond binnenklimaat. Lees meer over Zehnder.
loading...

Kom naar de Connected Construction Conference (voorheen SUM)

Op 25 mei 2023 is het zover: de Connected Construction Conference vindt plaats in de Jaarbeurs in Utrecht. U bent van harte uitgenodigd!

Voor onze trouwe klanten: dit evenement is vergelijkbaar met wat wij vroeger de “SUM” noemden! Voor onze iets minder trouwe (of nostalgische) klanten, check hier de aftermovie van de SUM 2018.

Leer, connect en laat u inspireren

-- Meer dan 15 sessies om uit te kiezen, onder andere over de beslissende rol van up-to-date content in BIM-projecten
-- Praktijkverhalen van VolkerWessels, EEG, Cordeel, en vele anderen
-- Netwerken met honderden branchegenoten
-- Ontmoet de CTO van Trimble Inc.
-- Demonstraties van nieuwe BIM software
-- Spot de robothond live in actie
-- Onafhankelijke waarborger Borg4 deelt tips voor de WKB

Dit gratis evenement is voor iedereen die werkzaam is in de bouwsector. Het programma is met veel aandacht in elkaar gezet om netwerken te faciliteren, maar tegelijkertijd een dagprogramma te leveren dat u zelf op maat kunt samenstellen zodat het in uw dag past.

Wij hopen u op 25 mei in Utrecht te ontmoeten!

Meer informatie en aanmelden: construction.trimble.nl/conference
loading...

New on MEPcontent: w-NEXT HD S & K chillers

New on MEPcontent.com! The w-NEXT HD S & K chillers (HD version) by Mitsubishi Electric Hydronics & IT Cooling Systems. These air conditioners for IT Cooling for chilled water feeding are now available for download in RFA, DWG and IFC format, in Revit 2020 and EMCS proof.

The following BIM models are available:

w-NEXT HD K U E1-E10
w-NEXT HD K-HCWT U E1-E10
w-NEXT HD S U E1 -E9

w-NEXT HD S: Air Conditioners for IT Cooling
• High cooling density version;
• Chilled water feeding;
• Variable air and water flow;
• Plug fans with EC electric motor.


This series, for perimeter installation, is offered in 10 models available in the following version:
• Downflow version (Under) characterized by air intake from the top and air delivery from the
bottom of the unit.

Cooling capacity: 14,7 ÷ 145,0 kW


w-NEXT HD K: Air Conditioners for IT Cooling
• High cooling density version;
• Operation with high chilled water temperature for the highest energy efficiency
• Chilled water feeding;
• Variable air and water flow;
• Plug fans with EC electric motor.

This series, for perimeter installation, is offered in 11 models available in the following version:
• Downflow version (Under) characterized by air intake from the top and air delivery from the
bottom of the unit.

Cooling capacity: 14,3 ÷ 183,0 kW

Key Features & Benefits

• Optimization of the hydraulic circuit;
• New plug fans with EC electric motors with impeller in composite material, which guarantees a
reduction of power consumption;
• New fans electric motor that do not require maintenance;
• Improvement of the control software, developed by MEHITS, with advanced control logic;
• Increased cooling density, up to 56,1 kW per m2;
• Operation with high chilled water temperature (K version) for the highest energy efficiency;
• Total front access for the routine maintenance;
• Panels fully removable to facilitate the operations of extraordinary maintenance.
loading...

Mise à jour PLS Saint-Gobain

Nous venons d’actualiser les fichiers PLS pour Stabicad du fabricant leader Saint Gobain:

Saint-Gobain SMU Plus avec 226 produits
Saint-Gobain SME avec 128 produits
Saint-Gobain SMU S avec 250 produits

À propos de Saint-Gobain
Leader mondial de la construction durable, Saint-Gobain conçoit, produit et distribue des matériaux et services pour les marchés de l’habitat et de l’industrie.

Développées dans une dynamique d’innovation permanente, ses solutions intégrées pour la rénovation des bâtiments publics et privés, la construction légère et la décarbonation du monde de la construction et de l’industrie apportent durabilité et performance.

L’engagement du Groupe est guidé par sa raison d’être « MAKING THE WORLD A BETTER HOME ».

Mise à jour PLS Lindab

Le PLS des conduits d'aération et pièces auxiliaires Safe line de Lindab à été étendu avec 650 produits, pour un total de 6695 produits Lindab disponibles en Stabicad !


Lindab Group
Le groupe industriel suédois Lindab, leader mondial du secteur de la ventilation, possède une expérience et un savoir-faire reconnus depuis plus de 60 ans dans la conception, la fabrication et la commercialisation de solutions de ventilation pour les bâtiments d’habitation, les locaux tertiaires et industriels, mais aussi les bâtiments maritimes (navires, plateformes offshore...).
loading...

Le Valetis, terminal de ventilation compact haute performance de Ubbink pour extraction de VMC simple et double-flux

Afin de répondre aux besoins actuels du marché de la construction neuve, Ubbink propose un nouveau terminal de ventilation haute performance pour VMC simple et double flux. Plus compact, plus performant, plus esthétique, plus polyvalent ... Dès maintenant aussi disponible comme fichier BIM sur la bibliothèque MEPcontent !

Un terminal haute performance
Le Valetis contribue à améliorer la performance des systèmes raccordés (VMC simple et double-flux, chauffe-eau thermodynamique) en limitant très fortement les pertes de charge du réseau de rejet.

Moins de pertes de charge
Le terminal Valetis génère très peu de pertes de charge permettant ainsi d’optimiser les performances du réseau de ventilation (les efforts demandés au moteur de la VMC pour extraire l’air sont moindres et le matériel est préservé dans le temps) et de maximiser la conformité lors du contrôle du réseau en fin de chantier (RE 2020) tout en compensant d’éventuelles problématiques au sein du réseau (écrasement de conduit…)

Plus polyvalent
Le terminal est équipé d’une Bavette Ubiflex® grande dimension (600 x 600 mm) permettant de s’adapter facilement aux toits avec des tuiles fortement galbées (type G3 ou tuiles canal) et ainsi assurer une étanchéité parfaite.

Une esthétique retravaillée
Son design innovant permet de limiter les phénomènes de salissures sur le toit dues à l’extraction de hotte ou VMC (tuiles ou ardoises connexes tachées).

En effet, grâce à sa conception, l’air est extrait de manière à ne pas être rejeté au contact direct des tuiles/ardoises connexes, permettant ainsi de conserver l’esthétique naturelle du toit.

Conforme à la réglementation
Le Valetis maximise la conformité du réseau lors du contrôle des débits à réception dans le cadre de la RE2020. Il est testé selon la dernière norme en vigueur (EN 13141-5 2020) et évalué par le laboratoire indépendant CETIAT certifié COFRAC. Il est conforme au DTU 68.3. Le terminal + réseau de rejet génère uniquement 10.3 Pa (pression totale) pour 200 m3/h alors que le DTU 68.3 exige < 25 Pa.

Pour en savoir plus, consultez le site web de Ubbink.
loading...

A uniform standard for MEP engineers globally

Out now! The updated Extended MEPcontent Standard (EMCS) 5.0 provides MEP engineers and manufacturers all around the world with a clear understanding of the content as it is offered on MEPcontent.com: consistent, uniform, compact and compliant to international and local BIM standards.

The standard has been rebranded to Trimble and updated with new and extended rules as well as new basic parameter values. The EMCS is a uniform standard for MEP engineers globally. Download the newest version now!
loading...

Carisma Whisper by Sabiana

The Carisma Whisper fan coil unit combines a beautiful design and a reduced overall depth with particularly interesting performance in terms of sound level and energy consumption.

Carisma Whisper is proposed in the MV wall-mounted version and in the IV built-in version; the MV version has a very reduced depth of 126 mm with a modern aesthetic that integrates very well with the furnishings of any type of home, maintaining excellent performance in terms of noise and consumption.

Carisma Whisper is available in 5 sizes and 2 versions (wall-mounted and built in), each equipped with a 2-row heat exchange coil. The Carisma Whisper series is equipped with a brushless BLAC (brushless) and sensorless (sensorless) permanent magnet electronic synchronous motor controlled by an inverter board designed and developed in Italy. The air flow rate can be varied continuously through a 1-10 V signal. High efficiency even at low number of revolutions allows a great reduction in electricity consumption with absorption values, in the most frequent conditions of use, not exceeding 5 Watts.

The sound levels are particularly low in all operating conditions, without any resonance phenomenon at any frequency.

A basic command and an advanced command with Bluetooth and Wi-Fi operation, in addition to the possibility of management via APP, make this fan coil the ideal solution for the air conditioning of any residential environment.

About Sabiana

Sabiana is an Italian company that has been designing, producing and selling innovative heating and air conditioning products for over 80 years. All of the products use the best existing natural liquid that has always stood side-by-side with humans in all of their activities: water.
In fact, by heating and cooling water, the climate of any work environment can be controlled with great precision and a high degree of comfort. Sabiana has paid a great deal of attention to the noise level of its products (it was the first Italian company to introduce radiant ceiling panels in industrial environments in 1973, providing heating without any noise), their electrical consumption (it was the first company to introduce Cassette fan coil units with electronic motors and low power consumption on the Italian market in 2009) and indoor air quality (it was the first company to adopt a patented electronic filter on a wide range of air conditioners in 1993).

Consistent with the great Italian ability to produce products with sophisticated design, Sabiana offers products that can be harmoniously added to any building's architectural structure.
The main product lines are:
o Radiant panels
o Unit heaters
o Fan Coils
o Air handling units
o Recovery Units
o Heat pumps
o Stainless steel flues
o Electric units

Over 50% of turnover is in foreign markets, especially in Europe, North and South America and the Middle East, with over 50 exclusive distributors. In Italy there are 45 Sales Agents who can recommend the Sabiana product that best fits your climate control needs.
loading...

Major PLS update regarding the Stago KG281 Cable Trays

The Stago KG281 Cable Trays product line sheet (PLS) for Stabicad has gone through a major update and has been completely reworked, improving the naming of the articles to match the manufacturer documentation and to increase the findability of the products within Stabicad. The PLS has also been extended with articles that were not available before.

The Stago product lines have been given a new name within Stabicad, to match with the recent takeover of the Wibe group. The Stago product name continues to apply for all 410 products, but when searching for a certain product, you will have to first search for Wibe, after which you can then select the Stago products (for example product type KG281). The well-known ladder track LB4000 can also be found under the Wibe name.

Please update your PLS files with care and take into consideration the impact it has on projects with articles that will be replaced or removed. As a Stabicad user, please reference this article for more information.

About Wibe Group
Wibe Group brings together four of the world’s leading cable management brands (Wibe, Stago, Mita and Defem) as a new independent company to offer a complete, innovative range of cable ladders, cable trays and mesh trays – for applications ranging from commercial buildings to extreme demanding industrial environments.

About Trimble
Trimble MEP delivers sophisticated solutions that transform workflows from the office to the field. The Trimble Constructible Process allows specialty trades to build beyond BIM to automate fabrication and fieldwork with reliable construction data. With access to the largest library of manufacturers' content and a broad portfolio of hardware and software solutions, Trimble optimizes the entire design, build, and operate lifecycle.
Dezember 2022
loading...

Vielen Dank

Der Jahreswechsel ist eine Zeit, in der wir uns auf das besinnen, was wirklich wichtig ist: Danke für Ihr Vertrauen, Ihre Unterstützung und für unsere gute Zusammenarbeit! Wir wünschen Ihnen ein frohes Weihnachtsfest und ein besonders gutes und erfolgreiches neues Jahr! Das MEPcontent-Team
November 2022
loading...

Latest content Mitsubishi Heavy

Mitsubishi Heavy recently published new BIM files and added the new ZTL and PAC standard Inverter FDC125VNP-W model, which also includes all the latest Wi-Fi models!

All models are available in Revit, Autocad and IFC formats.

Mitsubishi Heavy also created BIM files for the Hyozan C02 Refrigeration Condensing Unit, which is designed for medium temperature applications such as refrigeration, as well as low temperature applications for freezing. It has the world's first 2-stage compressor (rotary and scroll), also known as the GSR Hybrid Compressor. The unit provides easy installation with flexibility and workability with a long refrigerant pipe up to 100 meters and is applicable in a wide range of applications for refrigeration.

Mitsubishi Heavy will continue using smart BIM solutions in the future and adding more products from their RAC, PAC and VRF lines.

The BIM files can be downloaded on MEPcontent.com and via the Mitsubishi Heavy website.

About Mitsubishi Heavy
Mitsubishi Heavy Industries Air-Conditioning Europe (MHIAE) is committed to helping people live better wherever they're based. Whether that’s finding more energy efficient heating solutions to reduce greenhouse gas emissions or providing a reliable air-conditioned infrastructure in tough environments, we strive to offer a solution to an important aspect of life, temperature.

MHIAE offers high-efficiency systems for cooling and heating air and water in residential, commercial and industrial applications. As a reputable engineering company with vast expertise and experience, we are fully equipped to meet all your HVAC needs.
loading...

Stabicad’s mechanical calculations are verified by CIBSE

All of Stabicad’s mechanical calculations have passed CIBSE’s pioneering Software Verification Assessment program! This means you can dramatically increase your productivity and calculation accuracy directly in Revit.

Stabicad is the only software to have all of its mechanical building system design modules independently verified by CIBSE and we’re proud to be leading the way in the industry. Stabicad’s verified calculations include:

    Air systems
    Heating and cooling water systems
    Domestic water systems
    Drainage systems


Find out more
loading...

New from Spirotech

New content is available from Spirotech, the specialist in fluid conditioning for closed systems: it includes the safety expansion vessels EVN, EVU06 and EVU10 and the hydraulic manifold Spirocros AX-J.
loading...

New Daikin product series

Discover the new Daikin content available on MEPcontent and in Stabicad for France. Daikin is the world's leading manufacturer of heat pumps, ventilation and air conditioning systems and offers innovative and environmentally friendly solutions for private, commercial and industrial applications.
loading...

Saunier Duval update

For France, we have recently updated and improved several Saunier Duval products.
For example the ThemaPlus Condens, the IsoTwin Condens and the IsoMax Condens. Now EMCS compliant, with updated EMCS parameters, height, heating capacity and voltage.
loading...

Polymelt PLS and BIM files extension

The Polymelt Ecosan and the Polymelt Mechanical product line sheets (PLS) for Stabicad have been updated and extended! More than 750 new products are now available.

The Polymelt Mechanical PLS (previously Polo-Klima) includes 447 products. The Polymelt Ecosan PLS (previously Polo-Ecosan) contains 312 products. They are now available with localisations for the Benelux, France, UK, Germany and Romania.

Additional BIM files of the accessories and valves are also available and can be downloaded on MEPcontent.

Discover Polymelt’s latest innovations in this Polymelt video.

About Polymelt


The Polymelt brand has existed since 1968 and has since been synonymous with high-quality plastic pipe systems from southern Germany for customers and business partners. Due to a change of ownership and a merger in 2003, a new brand association was created under the Poloplast brand from Austria. In recent years, the company operated under the name Poloplast GmbH. At the turn of the year 2021/2022, this brand association was dissolved - returning to the tried and tested - and Poloplast GmbH became Polymelt GmbH again from January 2022. The company retains its location in Ebenhofen, Germany and the proven production facilities also remain as before. The best quality "Made in Germany". Polymelt operates as well in the United States, with Polymelt America Inc, based in Houston, Texas.

About Trimble


Trimble MEP delivers sophisticated solutions that transform workflows from the office to the field. The Trimble Constructible Process allows specialty trades to build beyond BIM to automate fabrication and fieldwork with reliable construction data. With access to the largest library of manufacturers' content and a broad portfolio of hardware and software solutions, Trimble optimizes the entire design, build, and operate lifecycle.
loading...

Revit 2023 support for Apps

Easily design Mechanical, Electrical and Plumbing systems with the MEPcontent Apps and with the MEPcontent Manufacturer Apps! They are all free to download and use. Now with Revit 2023 support!



Browse within the largest BIM library and enrich your project with manufacturer-specific and generic BIM content with our MEPcontent browser. Simply load or insert 3D content directly into your Revit model or CAD drawing. Without having to leave your project environment. Free to download and use.

As a structural engineer, you can now easily communicate with MEP engineers and contractors to manage openings at high speed. BIM means collaboration and the Openings App is specifically designed for it. Combining openings, approving or declining opening requests, creating voids in the architectural or structural model, as well as creating your response file can all be done quickly and effectively.

Easily design, manage and configure complete sets of switch ranges, even for the largest BIM projects, with the Switch Range Configurators of manufacturers ABB, Busch-Jaeger, Niessen and Jung. Experiment with the variety of design options and functions with the correct annotation offered by this App to streamline your design in both 2D and 3D. Always up to date with the latest product data available in your country.

The Mitsubishi Electric System Designer App for Revit and AutoCAD is the perfect choice to efficiently design air conditioning systems. Gain access to localized and up-to-date content, and make use of the advanced searching and filtering options to find the right equipment in a matter of seconds. Then start drawing pipes and fittings, and directly connect them to your equipment. All straight from within your project environment.

Our Product Line Placer Apps for Revit make it easy to design piping systems, sanitary systems, waste water and supply systems with accurate and localized content of your favorite manufacturer: Henco, Ostendorf, Poloplast, Sanha, Raccorderie Metalliche, Rubinetterie Bresciane Bonomi. Just click, draw, and the right fittings are automatically added to your system. Thanks to the autorouting functionality, the right fittings are automatically added to your system while drawing. Use the in-app predefined schedules and order your items directly from the material lists.

The calculations functionality for waste water systems of the Valsir Product Line Calculator is fully Revit integrated and EU compliant and reduces the chance of errors to a minimum with both design and calculation taking place in the App.

Discover all our Apps on MEPcontent and download them for free!
loading...

Discover the new Vaillant aroTHERM pure system: an efficient, affordable heat pump solution with a fast and space saving installation.

Introducing the new, easy to install air to water heat pump aroTHERM pure: The smallest and most light weighted outdoor unit in the Vaillant portfolio for efficient heating, cooling and DHW.
With a heating power of 4 to 10 kW and a COP of up to 5,2 (A7/W35) the aroTHERM pure offers an entry level heat pump with enormous potential. This new air to water heat pump is especially suited for:

    - One and multiple family new built homes
    - A distance of up to 40 m between indoor and outdoor unit
    - Up to 30 m distance in height, therefore it is also possible to install in buildings of up to 8 floors
    - Installation also possible in coast areas (after ISO-Norm 12944-6)

    The aroTHERM pure pre-mounted indoor units are as small as a fridge and bring a compact solution for balcony and kitchen installation. With its small dimensions, low weight of only 55 and 82 kg and the split mounting system, transport has never been easier. The indoor unit uniTOWER pure brings better accessibility to all components as today for better service and repair from the front. Additional accessories can be integrated to fulfill customers’ requirements.

    Protect the environment with currently one of the best refrigerants for split units: R32. This is one of the best alternatives for the new refrigerant split heat pumps as aroTHERM pure. It has a lower global warming potential than conventional refrigerants and is used in smaller amounts. For split refrigeration systems, R32 is the economical alternative to our natural refrigerant R290. The market launch will be in February 2023. The launch date may differ in some countries. For further information, please visit our website or your country specific Vaillant website.
September 2022

Priva launches BIM library on MEPcontent.com

BIM library


Priva Horticulture recently launched its BIM library on MEPcontent.com. This library contains BIM files of climate computers, measuring boxes, water systems and other hardware, among others. These files will help you speed up the digital plant design process. Check out Priva's offering on MEPcontent here!

About Priva


At Priva, we are driven by technological innovation in horticulture. Developing new greenhouse technology for controlled environments is our passion. We offer varieties of process computers, sensors and Cloud-based software with smart interactions to automate greenhouse systems. Modern greenhouse technology enables growers to produce fresh, safe and healthy food in a smart and sustainable way. We are proud that our solutions result in lower use of natural resources such as energy and water.

Besides horticulture, buildings such as hospitals, hotels and offices are controlled by our building automation systems and our AI services for energy optimisation. With AI, robotics and vision technology, we are developing new solutions together with partners to support smart buildings and autonomous greenhouses.

Want to know more about Priva or get in touch? Visit priva.com.